{"id":5402,"date":"2026-09-08T06:52:05","date_gmt":"2026-09-07T22:52:05","guid":{"rendered":"https:\/\/www.fskitchensink.com\/pressed-vs-handmade-stainless-steel-kitchen-sinks-distributors\/"},"modified":"2026-09-08T10:36:44","modified_gmt":"2026-09-08T02:36:44","slug":"pressed-vs-handmade-stainless-steel-kitchen-sinks-distributors","status":"publish","type":"post","link":"https:\/\/www.fskitchensink.com\/es\/pressed-vs-handmade-stainless-steel-kitchen-sinks-distributors\/","title":{"rendered":"Pressed vs Handmade Stainless Steel Kitchen Sinks: How Distributors Should Plan the Range"},"content":{"rendered":"

Direct answer:<\/strong> pressed (drawn) sinks and handmade (welded) sinks are two different product families, not two grades of the same product. Pressed sinks are formed from a single sheet by drawing, which suits high-volume, price-led programmes. Handmade sinks are cut, folded and welded by hand, which suits buyers who need heavier steel, tighter geometry and a more defined rim profile. Most distributors need both, because they serve different shelf positions and different buyers.<\/p>\n

Who this guide is for<\/h2>\n

This guide is written for importers, distributors, wholesalers, kitchen cabinet suppliers, countertop fabricators and OEM\/private-label buyers who are deciding how to split a stainless steel sink programme between pressed and handmade construction. It is not a consumer buying guide; the questions here are assortment, specification and ordering questions.<\/p>\n

The two families, defined<\/h2>\n

Pressed (drawn) stainless steel kitchen sink.<\/strong> A flat stainless sheet is placed in a press and drawn into a bowl in one movement. The bowl and the top surface come from the same piece of steel, so there are no welded seams inside the bowl. Corners are radiused because the steel has to stretch. Wall thickness is limited by what the sheet can tolerate during drawing.<\/p>\n

Handmade (welded) stainless steel kitchen sink.<\/strong> The steel is cut, bent and welded. Because the bowl is built rather than stretched, the maker can use thicker material and hold a tighter corner radius. The welds are ground and finished, and the finished sink is noticeably heavier.<\/p>\n

Side-by-side comparison<\/h2>\n\n\n\n\n\n\n\n\n\n\n\n\n
Decision factor<\/th>\nPressed (drawn)<\/th>\nHandmade (welded)<\/th>\n<\/tr>\n<\/thead>\n
How it is made<\/td>\nSingle sheet drawn in a press<\/td>\nCut, folded and welded<\/td>\n<\/tr>\n
Typical steel thickness range<\/td>\nAbout 0.4\u20130.8 mm<\/td>\nAbout 1.0\u20133.0 mm<\/td>\n<\/tr>\n
Corner geometry<\/td>\nLarger radii (stretching limit)<\/td>\nTighter radii possible<\/td>\n<\/tr>\n
Seams inside the bowl<\/td>\nNone<\/td>\nWelded and finished seams<\/td>\n<\/tr>\n
Weight<\/td>\nLighter<\/td>\nHeavier<\/td>\n<\/tr>\n
Typical MOQ<\/td>\n200 pcs per model<\/td>\n50 pcs per model<\/td>\n<\/tr>\n
Shelf position<\/td>\nVolume \/ entry to mid<\/td>\nMid to premium<\/td>\n<\/tr>\n
Best fit<\/td>\nProject supply, retail chains, price-led tenders<\/td>\nKitchen studios, renovation channel, specification-led buyers<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

Thickness figures above are the general ranges used for these two construction families. Confirm the exact thickness for each model on its product page or in your quotation, because thickness is specified per model, not per category.<\/em><\/p>\n

What each family means for your assortment<\/h2>\n

Pressed sinks carry the volume.<\/strong> Because the tooling does the shaping, unit cost stays lower and repeatability is high across large runs. This is the family you put behind a tender price or a retail promotional plan. The trade-off is flexibility: a pressed model needs its own tooling, so changing a dimension usually means a new tool, and the 200 pcs per model minimum reflects that.<\/p>\n

Handmade sinks carry the margin.<\/strong> The lower 50 pcs per model minimum lets you test a size or a finish without committing to a full pressed run. Heavier steel and a defined rim read as quality in a showroom, which is why kitchen studios and renovation-focused distributors tend to lead with handmade and stock pressed underneath it.<\/p>\n

Quartz composite sits beside both, not instead of them.<\/strong> Quartz composite kitchen sinks are also available and are ordered on a third MOQ level (20 pcs per model). Treat quartz as a complementary category for buyers who want a colour and a matte surface rather than as a replacement for stainless.<\/p>\n

Common sourcing mistakes<\/h2>\n